3.2. Specifications
The recommended lubricants and liquids
|
|
The lubricants and liquids recommended for use of cars by the company manufacturer at the time of drawing up the present manual are listed below. Fresher information can be obtained at company car repair shops of the Honda company. |
| Characteristic |
Value |
Motive oil: |
|
Type | Universal SG, SH or SJ oils on API |
Viscosity | Are specified in the card (see an illustration below) |
Type of transmission liquid for AT | ATF Honda Premium Formula |
Type of transmission liquid for CVT | ATF Honda CVT |
Type of gearbox oil for RKPP | MTF Honda |
Type of brake fluid | DOT 3 |
Type of liquid of system of hydrostrengthening of a wheel | Hydraulic liquid for the steering Honda amplifier |
Fuel type | Unleaded gasoline with octane number not lower than 87 |
Card of viscosity of motive oils
| |
|
Volumes of working liquids, l *
| Characteristic |
Value |
Motive oil |
|
Civic |
|
D16Y5 engine | 3.3 |
D16Y7 engine | 3.6 |
D16Y8 engine | 3.3 |
Integra | |
B18B1 engine | 3.8 |
B18C1 and B18C5 engines | 4.0 |
Transmission liquid for AT (depletion and filling) | 2.7 |
Transmission liquid for CVT (depletion and filling) | 3.9 |
RKPP | |
Civic | 1.8 |
Integra | 2.2 |
Cooling liquid | |
Civic | 3.0 |
Integra | |
B18B1 engine | 4.4 |
B18C1 and B18C5 engines | 4.7 |
* All volumes are specified only approximately. At adjustment be verified with-level tags. | |
System of ignition
| Characteristic |
Value |
Spark plugs | |
Civic | |
D16Y5 engine | |
Type | NGK ZFR4F-11 |
Interelectrode gap, mm | 0.99÷1.09 |
D16Y7 and D16Y8 engines |
|
Type | NGK ZFR5F-11 |
Interelectrode gap, mm | 0.99÷1.09 |
Integra |
|
Usual |
|
Type | NGK ZFR4F-11 |
Interelectrode gap, mm | 0.99÷1.09 |
Platinum |
|
Type | NGK PFR4G-13 |
Interelectrode gap, mm | 1.19÷1.29 |
Resistance of candle wires, Ohm | Not higher than 25 000 |
Ignition order | 1-3-4-2 |
Arrangement of cylinders and direction of rotation of the distributor of ignition
| |
|
Cooling system
| Characteristic |
Value |
| Temperatures of operation of the thermostat, °C |
|
| Beginning of opening |
79 |
| Full opening |
91 |
Size of a deflection of driving belts of auxiliary units, mm
| Characteristic |
Value |
Steering pump |
|
New belt | 9.5÷12.7 |
The belt which was in the use | 12.7÷15.9 |
Generator
| Characteristic |
Value |
Models without To/in | |
New belt | 9.5÷12.7 |
The belt which was in the use | 6.4÷11.1 |
Models with To/in |
|
New belt | 4.8÷7.9 |
The belt which was in the use | 9.5÷12.7 |
Brake system
| Characteristic |
Value |
Minimum admissible thickness of frictional overlays of blocks of disk brake mechanisms, mm | 1.6 |
Minimum admissible thickness of frictional overlays of boots of drum brake mechanisms, mm | 2.4 |
Adjustment of the parking brake | 6÷10 of clicks of a ratchet |
Idling turns (in a minute)
Characteristic | Value |
| Civic | |
D16Y5 engine | |
RKPP | 670 ± 50 |
AT and CVT | 700 ± 50 |
D16Y7 and D16Y8 engines |
|
| USA | |
RKPP | 670 ± 50 |
AT and CVT | 700 ± 50 |
Canada | 750 ± 50 |
Integra |
|
B18B1 and B18C1 engines | 750 ± 50 |
B18C5 engine | 800 ± 50 |
Parameters of the general adjustments
| Characteristic |
Value |
Valvate gaps (at the cold engine), mm | |
Civic | |
Inlet valves | 0.178÷0.229 |
Final valves | 0.229÷0.279 |
Integra |
|
B18B1 engine |
|
Inlet valves | 0.076÷0.127 |
Final valves | 0.152÷0.203 |
B18C1 and B18C5 engines |
|
Inlet valves | 0.152÷0.178 |
Final valves | 0.178÷0.203 |
Efforts of tightening of threaded connections, Nanometer
| Connection type |
Value |
| Drain stopper of AT and CVT | 49 |
| Drain stopper of RKPP | 39 |
| Jellied stopper of RKPP | 45 |
| Fuel filter |
|
| Hollow bolt | 14.9 |
| Nut of a hollow bolt | 22 |
| Spark plugs | 17.6 |
Nuts of fastening of wheels | 110 |